Kizashi Club

Your Kizashi Owners Club and Forum 

The Do It Yourself section is used provide assistance with mods and fixes. Whenever you are making a change to your car please take pictures and notes. Let others know what to watch out for and any useful tricks you learn. If you are starting a post in this section from scratch please hold it to a higher standard than you would for other forum posts. i.e. technical detail and even grammar.
Please post about issues or problems in the Technical Support & Problem Troubleshooting forum.
 #48788  by SAEED_KIZZY
 Sat Feb 02, 2019 1:26 pm
I found OEM rear spoiler on Megazip warehouse in UAE and order it.
my car had no rear spoiler so I have to make 4 holes on my trunk to fit spoiler, 2 for 7mm screw and 2 for plastic fastener.
and also I have some difficulties for stop light because it is different from OEM type.
I decided to cut some pieces of spoiler and make it fit to my car stop light.
Attachments
photo_2019-02-02_15-46-05.jpg
photo_2019-02-02_15-46-05.jpg (43.3 KiB) Viewed 1603 times
photo_2019-02-02_15-45-54.jpg
photo_2019-02-02_15-45-54.jpg (58.94 KiB) Viewed 1603 times
photo_2019-02-02_15-45-49.jpg
photo_2019-02-02_15-45-49.jpg (63.35 KiB) Viewed 1603 times
photo_2019-02-02_15-45-31.jpg
photo_2019-02-02_15-45-31.jpg (103.2 KiB) Viewed 1603 times
photo_2019-02-02_15-46-09.jpg
photo_2019-02-02_15-46-09.jpg (152.86 KiB) Viewed 1603 times
photo_2019-02-02_15-45-59.jpg
photo_2019-02-02_15-45-59.jpg (106.11 KiB) Viewed 1603 times
photo_2019-02-02_15-46-56.jpg
photo_2019-02-02_15-46-56.jpg (87.08 KiB) Viewed 1603 times
 #48943  by SAEED_KIZZY
 Sat Mar 02, 2019 8:23 pm
Kimgraesdal wrote:Did you use screws?

Yes OEM spoiler comes with 2 screws with nut and also 2 plastic clips on edge.
so I have to cut 4 holes in trunk lid.
 #48945  by SAEED_KIZZY
 Sat Mar 02, 2019 8:51 pm
Kimgraesdal wrote:Is it easy, is there any "pre hole" in the trunk

Yes half an hour work I think really easy.
No pre holes I had to drill 4 holes.
off course it is better to replace stop light with rear spoiler type to fit this spoiler but it costs 72$ so I decided to use my stop light instead and do some little modification to spoiler to fit.
 #50556  by SAEED_KIZZY
 Sat Oct 05, 2019 6:53 pm
About a month ago I made a discovery :D and found this hole and cap on each door

photo_2019-10-05_21-06-17.jpg
photo_2019-10-05_21-06-17.jpg (124.68 KiB) Viewed 238 times


and I do some research and find out this hole use to mount side sill guard and technically can be mounted on my kizashi so I ordered parts and it turn out really fully compatible.to install side sill guards I have to drill some holes in door.

photo_2019-10-04_14-26-02.jpg
photo_2019-10-04_14-26-02.jpg (37.93 KiB) Viewed 238 times


I made a template for guards and use it to drill and it really helped a lot.

photo_2019-10-05_21-14-25.jpg
photo_2019-10-05_21-14-25.jpg (37.9 KiB) Viewed 238 times


there are 4 plastic clips and one bolt and nut for each door. and final results:

photo_2019-10-05_21-18-12.jpg
photo_2019-10-05_21-18-12.jpg (61.81 KiB) Viewed 238 times

photo_2019-10-05_21-18-19.jpg
photo_2019-10-05_21-18-19.jpg (77.73 KiB) Viewed 238 times

photo_2019-10-05_21-16-42.jpg
photo_2019-10-05_21-16-42.jpg (217.81 KiB) Viewed 238 times
Attachments
photo_2019-10-05_21-14-25.jpg
photo_2019-10-05_21-14-25.jpg (37.9 KiB) Viewed 238 times
 #50557  by Ronzuki
 Sun Oct 06, 2019 12:52 pm
Nice work! Gutsy move to drill holes in perfectly good sheet metal, however, your daring efforts were rewarded.
 #50558  by SAEED_KIZZY
 Sun Oct 06, 2019 2:32 pm
Ronzuki wrote:Nice work! Gutsy move to drill holes in perfectly good sheet metal, however, your daring efforts were rewarded.

Thanks Ronzuki :D