Search found 277 matches
- Mon Jan 27, 2025 9:23 pm
- Forum: Kizashi Technical Support & Problem Troubleshooting
- Topic: OIL ON DRIVE
- Replies: 3
- Views: 2797
Re: OIL ON DRIVE
If you have an AWD model, I would have someone check the transfer case and rear differential fluid levels. Those hold less than a quart of gear oil each, so a very small leak (such as you appear to have) can become problematic before you realize something is wrong
- Fri Aug 30, 2024 2:32 pm
- Forum: Kizashi DIY Write-ups & Posts
- Topic: Heated Power Seat Installation
- Replies: 14
- Views: 36919
Re: Heated Power Seat Installation
I have a smaller white seat connector/harness that doesn't fit. I have seats ready to put in, but the connection doesn't work so what can I do? :cry: My experience comes only from the Kizashi as sold here in the US. I can't speak to what differences exist in the Kizashi sold in other markets. While...
- Sat Jul 06, 2024 3:12 pm
- Forum: Kizashi Technical Support & Problem Troubleshooting
- Topic: AC FLASHING AUTO
- Replies: 10
- Views: 8011
Re: AC FLASHING AUTO
I don't have any particular experience here, just access to the diagnostic info. The second pdf I posted with the codes points to 30.1 potentially being a wiring problem or short between the panel and control module. I think that a failure to clear would just mean that it is a current active code, n...
- Fri Jul 05, 2024 2:44 pm
- Forum: Kizashi Technical Support & Problem Troubleshooting
- Topic: AC FLASHING AUTO
- Replies: 10
- Views: 8011
Re: AC FLASHING AUTO
Yep, see the attached files:
- Fri Jul 05, 2024 2:40 pm
- Forum: Kizashi Technical Support & Problem Troubleshooting
- Topic: AC FLASHING AUTO
- Replies: 10
- Views: 8011
Re: AC FLASHING AUTO
I changed both the panel and the module. The climate control part and the bcm behind inside the dash. I don’t think the scanner was communicating with the hvac system. Could you recommend a scanner that would work? I believe there is some magic button pushing you can do on the climate panel to get ...
- Tue Jun 04, 2024 2:05 pm
- Forum: Kizashi Technical Support & Problem Troubleshooting
- Topic: 2013 Suzuki kizashi gts torque specs
- Replies: 2
- Views: 3199
Re: 2013 Suzuki kizashi gts torque specs
From the Service manual:
M8 cover bolts - 25 Nm (18.5 ft lb)
M10 cover bolts - 55 Nm (40.5 ft lb)
Crank pulley bolt - 150 Nm (111 ft lb)
Here is the pattern:
M8 cover bolts - 25 Nm (18.5 ft lb)
M10 cover bolts - 55 Nm (40.5 ft lb)
Crank pulley bolt - 150 Nm (111 ft lb)
Here is the pattern:
- Mon Jan 08, 2024 2:52 am
- Forum: Kizashi DIY Write-ups & Posts
- Topic: few quick questions
- Replies: 8
- Views: 12527
Re: few quick questions
Hi, I recently bought a sport gts and was going to switch my heated leather seats from my sls into my gts, I have seen one post talking about this but it never finished and has since stopped being posted or updated so ill ask my question here. How difficult is it to get the heated seat option to wo...
- Thu Oct 12, 2023 2:52 pm
- Forum: Chat About the Kizashi
- Topic: Cracked Tank
- Replies: 8
- Views: 7712
Re: Cracked Tank
A copy of the recall notice can be found here: https://static.nhtsa.gov/odi/rcl/2018/RCMN-18V769-7947.pdf You can also look up the recall notice and find your nearest Suzuki service center on the suzukiauto site: https://www.suzukiauto.com/ You should contact Suzuki, or your nearest service center a...
- Thu Aug 31, 2023 1:40 pm
- Forum: Kizashi Technical Support & Problem Troubleshooting
- Topic: Suzuki Kizashi Drive Cycle
- Replies: 8
- Views: 5484
Re: Suzuki Kizashi Drive Cycle
I've not seen a specific drive cycle listed for the Kizashi, but it you have an OBDII scan tool it will probably be able to tell what monitors have been completed, which have not, and if the vehicle is ready for an emissions check
- Fri Jun 16, 2023 12:38 pm
- Forum: Kizashi Technical Support & Problem Troubleshooting
- Topic: Fluid Change - Transmission Trouble
- Replies: 10
- Views: 18281
Re: Fluid Change - Transmission Trouble
Hey buddy, are you able to resolve the issue? I am also conisdering a transmission oil change soon. Currently at 245k km (bought at 198k km). Any suggestions? My suggestion would be to just start by doing a drain and fill and leave the pan and pan filter/pickup alone. That will take about 3.8L of C...