Kizashi Club

Your Kizashi Owners Club and Forum 

The Do It Yourself section is used provide assistance with mods and fixes. Whenever you are making a change to your car please take pictures and notes. Let others know what to watch out for and any useful tricks you learn. If you are starting a post in this section from scratch please hold it to a higher standard than you would for other forum posts. i.e. technical detail and even grammar.
Please post about issues or problems in the Technical Support & Problem Troubleshooting forum.
 #49049  by SAEED_KIZZY
 Fri Mar 22, 2019 8:02 pm
Hi everybody
My car do not have useful options which is available in full version SDLX. options like Parking Sensor, Auto light ON and rain sensor, Xenon headlight, and Headlight washer and also cruise control.
so I decided to started a project to add some OEM options and come up with these sub projects:
1- Cruise control
2- light and rain sensor
3- Parking Sensor
4- Headlight Washer

cruise control(1) only needed OEM steering wheel with cruise key control the rest is done by ECM.
but other sub project need more technical information and wiring because you can by OEM parts for specific option but no wiring is exist in car. for example for rain sensor you need to wire CAN bus signal and also power and ground to rain sensor.
In following posts I decided to explain how to do that and show the result maybe these information is useful for someone else.
 #49051  by SAEED_KIZZY
 Mon Mar 25, 2019 8:13 pm
Install Rain and light sensor:
auto light and automatic wiper control in kizashi is managed by BCM (Body Control Module) but in order to do that BCM need Rain/light sensor module, this module is placed in front glass in predefined location.
rain/light sensor communicate with BCM module through CAN bus.
As always I bought parts from megazip.net
in order to activate this module 2 types of wiring needed
1- power and ground: I use ACC power from G248 connector(Audio System connector).
2- need 2 wires for CAN bus connectivity: I use HVAC unit and tap to WHT and RED wire connected to it. those wires are twisted wire by default.
unfortunately there is no predefined location to mount rain/light sensor module so I use 3M double sided tape (clear type) to mount this unit.
after wiring in first time I turn ON my car autolight LED on cluster is flashing 1s telling me to calibrate this module and after calibration autolight and wiper is working properly.
rain/light sensor module
20190203_135441.jpg
20190203_135441.jpg (207.56 KiB) Viewed 2023 times


HVAC module
20190204_173035.jpg
20190204_173035.jpg (137.91 KiB) Viewed 2023 times
Attachments
photo_2019-03-25_23-40-27.jpg
photo_2019-03-25_23-40-27.jpg (73.95 KiB) Viewed 2023 times
 #49060  by SAEED_KIZZY
 Fri Mar 29, 2019 3:00 pm
Autolight update:
in order to activate auto light kizashi uses Auto mode in headlight switch I use simple ON/OFF switch to manually do the job.
yesterday I decided to disassemble headlight switch and found out wire for AUTO mode is missing so I soldered new wire to headlight switch also cut some pieces of switch to add new position in switch and it worked! I just saved 90$ :D :D
in my modification in OFF position system in actually in AUTO mode.


photo_2019-03-29_18-25-22.jpg
AUTO MODE in OFF position
photo_2019-03-29_18-25-22.jpg (54.68 KiB) Viewed 1957 times


photo_2019-03-29_18-25-41.jpg
OFF in next position
photo_2019-03-29_18-25-41.jpg (63.79 KiB) Viewed 1957 times
 #49080  by SAEED_KIZZY
 Sun Mar 31, 2019 3:16 pm
Time for Headlight Washer project
headlight washer contain this parts
1- Washer motor
2- hoses and clips
3- actuator and cap
4- controller module

you can see parts in pic bellow

photo_2019-03-31_18-08-57.jpg
photo_2019-03-31_18-08-57.jpg (91.54 KiB) Viewed 1882 times


this unit is a separate unit and no communication with any module in car just uses some signals in kizashi to do the task of controlling washer motor. actuator is mechanical part and just work with water pressure. controller is simple module with 6 Pin connector this module use those signals:
1- power and ground(use IG2 power signal) in my car I use ACC instead of IG2
2- headlight signal
3- headlight washer switch
4- windshield washer signal
5- signal to control washer motor
also headlight washer uses 12V from battery to supply current to drive motor this signal is come from engine fuse box

photo_2019-03-31_18-25-04.jpg
photo_2019-03-31_18-25-04.jpg (134.08 KiB) Viewed 1882 times


to install washer motor I need to drill a hole in washer tanks

photo_2019-03-31_18-32-06.jpg
photo_2019-03-31_18-32-06.jpg (124.49 KiB) Viewed 1882 times

photo_2019-03-31_18-33-17.jpg
photo_2019-03-31_18-33-17.jpg (56.12 KiB) Viewed 1882 times

photo_2019-03-31_18-39-36.jpg
photo_2019-03-31_18-39-36.jpg (76.74 KiB) Viewed 1882 times


then installing hoses

photo_2019-03-31_18-27-20.jpg
photo_2019-03-31_18-27-20.jpg (98.68 KiB) Viewed 1882 times

photo_2019-03-31_18-26-50.jpg
photo_2019-03-31_18-26-50.jpg (274 KiB) Viewed 1882 times



then I have cut rectangle hole in front bumper. fortunately there is drawing in back of bumper to designate cutting area for actuator( thanks to Suzuki engineers :D )

photo_2019-03-31_18-27-09.jpg
photo_2019-03-31_18-27-09.jpg (60.07 KiB) Viewed 1882 times


and here final result :D :D
photo_2019-03-31_18-26-03.jpg
photo_2019-03-31_18-26-03.jpg (66.83 KiB) Viewed 1882 times

photo_2019-03-31_18-36-28.jpg
photo_2019-03-31_18-36-28.jpg (118.78 KiB) Viewed 1882 times
 #50550  by SAEED_KIZZY
 Fri Oct 04, 2019 12:13 pm
quick update on headlight washer:
it turns out I made mistake to mount hoses.
hoses should be mounted on front bumper and there are mounting points for metal clips and it make perfect sense now this way disassembling front bumper is so easier :D
photo_2019-10-04_14-42-38.jpg
photo_2019-10-04_14-42-38.jpg (97.66 KiB) Viewed 117 times

photo_2019-10-04_14-42-33.jpg
photo_2019-10-04_14-42-33.jpg (103.28 KiB) Viewed 117 times

photo_2019-10-04_14-42-23.jpg
photo_2019-10-04_14-42-23.jpg (136.66 KiB) Viewed 117 times